DIY一个RFID音乐盒-回味老歌，致敬经典
https://v.youku.com/v_show/id_XNDU5NDE4Mzc0MA==.html?spm=a2hzp.8244740.0.0这次以RFID音乐盒为载体，回味老歌，致敬经典
听的是老歌 咀嚼的是青春回忆
一首首经典老歌,勾起我们逝去的青春记忆
“每一首老歌的背后都藏着你我的青春记忆，有考试时的紧张，有情窦初开的甜蜜，还有大考后的放松，也有失恋的难过……。”
那些经典歌曲总能穿破岁月的灰尘，越过遗忘的脑海，复活在每个人的心中。让我们坐上重返青春的列车，一起聆听那真挚、浪漫、一尘不染的美妙之声。
聆听这样的歌声，总使人有时光倒流的感觉，仿佛又回到了从前，回到了我们年轻的时候，让我们致敬经典，致敬曾经的歌坛巨星。致敬那一去不返的青春。
值此大疫之时，历尽沧桑不低头，归来日快意人生。
项目所需硬件如下：
1.arduino UNO
2.DFPlayer MINI
3.RC522和6个钥匙扣Tag
硬件连线图
/*
*
This Sketch is made by gada888
-----luoyang-China------
-----2020-03-18----------
*/
#include <SPI.h>
#include <MFRC522.h>
#include "Arduino.h"
#include "SoftwareSerial.h"
#include <DFPlayerMini_Fast.h>
#define SS_PIN 10
#define RST_PIN 9
MFRC522 mfrc522(SS_PIN, RST_PIN); // Create MFRC522 instance.
SoftwareSerial mySerial(7, 6); // RX, TX
DFPlayerMini_Fast myMP3;
void setup()
{
mySerial.begin(9600);
myMP3.begin(mySerial);
myMP3.volume(23);
Serial.begin(115200); // Initiate a serial communication
SPI.begin(); // InitiateSPI bus
mfrc522.PCD_Init(); // Initiate MFRC522
Serial.println("Approximate your card to the reader...");
Serial.println();
}
void loop()
{
// Look for new cards
if ( ! mfrc522.PICC_IsNewCardPresent())
{
return;
}
// Select one of the cards
if ( ! mfrc522.PICC_ReadCardSerial())
{
return;
}
//Show UID on serial monitor
Serial.print("UID tag :");
String content= "";
byte letter;
for (byte i = 0; i < mfrc522.uid.size; i++)
{
Serial.print(mfrc522.uid.uidByte < 0x10 ? " 0" : " ");
Serial.print(mfrc522.uid.uidByte, HEX);
content.concat(String(mfrc522.uid.uidByte < 0x10 ? " 0" : " "));
content.concat(String(mfrc522.uid.uidByte, HEX));
}
Serial.println();
Serial.print("Message : ");
content.toUpperCase();
if (content.substring(1) == "69 E4 3C A3") //change here the UID of the card/cards that you want to give access
{
Serial.println("Authorized access");
Serial.println();
myMP3.play(1);
delay(1000);
}
if (content.substring(1) == "67 33 7E 7A") //change here the UID of the card/cards that you want to give access
{
Serial.println("Authorized access");
Serial.println();
myMP3.play(2);
delay(1000);
}
if (content.substring(1) == "D7 3F 7C 7B") //change here the UID of the card/cards that you want to give access
{
Serial.println("Authorized access");
Serial.println();
myMP3.play(3);
delay(1000);
}
if (content.substring(1) == "F7 E6 51 7B") //change here the UID of the card/cards that you want to give access
{
Serial.println("Authorized access");
Serial.println();
myMP3.play(4);
delay(1000);
}
if (content.substring(1) == "E7 B6 72 7B") //change here the UID of the card/cards that you want to give access
{
Serial.println("Authorized access");
Serial.println();
myMP3.play(5);
delay(1000);
}
if (content.substring(1) == "37 18 84 7B") //change here the UID of the card/cards that you want to give access
{
Serial.println("Authorized access");
Serial.println();
myMP3.play(6);
delay(1000);
}
if (content.substring(1) == "87 2E 79 7A") //change here the UID of the card/cards that you want to give access
{
Serial.println("Authorized access");
Serial.println();
myMP3.play(7);
delay(1000);
}
else {
Serial.println(" Access denied");
delay(1000);
}
}
代码运行后，打开串口COM。按个去试每一个钥匙扣Tag，可以看到COM口给出的每个Tag的UID代码。把他们抄下来，写在每个tag后面，让再填入程序的if-else
语句里。这个程序里我填的都是我买的Tag码，记住：每个Tag的UID码都不一样，你需要填你自己的。
在SD卡里copy入以下mp3文件
硬件测试如下
本来想用3D打印机打印明星的，后来因为3D部分学艺不精，放弃了。改用纸盒了。
这个每次用Tag识别时候，都要先按Reset键一下，其次，识别完的纸盒人要放在RC522旁边，因为我设置的是每秒识别一次Tag，放在它上面，就会每秒从头放mp3.
66666 您的rfid模块在哪买的? 20060606 发表于 2020-7-31 05:48
您的rfid模块在哪买的?
在某宝，商家叫‘明武电子’
页:
[1]