论坛 › 激光切割 › 激光切割+编程 时针

大银子 发表于 2021-7-7 11:29:57

激光切割+编程 时针

一个会转动的时钟，上面会坐一个小人，旁边摆个小桌子。每过一段时间，小人就会转走来提醒程序员该休息了。


Clockwork
Spring 2015
Alex Greenspan
Greta Gardner
Andy Mah


| Column 1 | Column 2 | Column 3 |
| -------- | -------- | -------- |
||| |
||| |
||| |


```
#include <Servo.h>// servo library

// LIGHT SENSOR RELATED VARIABLES
const int sensorPin = 0; // Light sensor in A0
int prevLightLevel = 1023; // global variable for previous light level
int lightLevel; // global variable for light level
const int midLight = 400; // make 200 for normal use, 400 for testing

// SERVO RELATED VARIABLES
Servo servo; // servo control object
int startAngle;
int currentAngle;
int angleHigh;
int angle = 0;
const int angleStep = 10; // number of angles to rotate per loop
const int highestAngle = 180;
const int lowestAngle = 30; // adjusted for backward rotate

// TIME RELATED VARIABLES
unsigned long startTime; // start time
unsigned long elapsedTime; // elapsed time

void setup()
{
servo.attach(9); // begin sending control signals to the servo
servo.write(lowestAngle); // start servo at the lowest angle
Serial.begin(9600); // for testing purposes
}

void loop()
{
lightLevel = analogRead(sensorPin); // check if someone is sitting
// Serial.println(lightLevel); // print light level
// delay(1000);

if (lightLevel <= midLight && prevLightLevel > midLight) { // just started sitting AKA SETUP
    //Serial.println("GET HERE");
    startTime = millis(); // start the timer
    currentAngle = lowestAngle; // make sure currentAngle is given a number -> lowest angle
    Serial.println("Begin sitting at starting position");

} else if (lightLevel <= midLight && prevLightLevel <= midLight) { // still sitting AKA ACTIVE
    elapsedTime = millis() - startTime; // clock the elapsed time since started sitting
    if (elapsedTime % (1000*5) == 0) { // 5 seconds passed, time to rotate
      // Usually prints three of the below at once, so make sure it rotates less to account for it
      forward_rotate();
      //Serial.println("current angle is " + currentAngle);
    }

} else { // finished sitting
    //Serial.println(currentAngle);
    if (currentAngle != lowestAngle) {
      backward_rotate();
    }
}

prevLightLevel = lightLevel; // update prev light level to current light level
}

void forward_rotate()
{
if (angleStep + currentAngle < highestAngle) {
    angleHigh = angleStep + currentAngle;
} else {
    angleHigh = highestAngle;
}
for(angle = currentAngle; angle < angleHigh; angle++)
{                                 
    servo.write(angle);               
    delay(30); // used to be 15               
}
currentAngle = angleHigh;
Serial.print("Current angle is: ");
Serial.println(currentAngle);
Serial.println(lightLevel);
}

void backward_rotate()
{
Serial.println(lightLevel);
for(angle = currentAngle; angle > lowestAngle; angle--)   
{                              
    servo.write(angle);         
    delay(60); // used to be 15      
}
currentAngle = lowestAngle; // reset currentAngle
Serial.println("Reset back to starting position");
}
```




原文：https://www.hackster.io/alexsg/clockwork-82a828

诩 发表于 2022-5-8 10:10:03

有视频演示吗？

三春牛-创客 发表于 2023-8-4 22:40:51

厉害厉害

三春牛-创客 发表于 2023-8-4 22:41:53

赞赞赞赞赞！

三春牛-创客 发表于 2023-8-4 22:43:01

有视频演示吗？有的话就更好了。

花生编程 发表于 2023-8-5 22:21:56

厉害厉害

花生编程 发表于 2023-8-5 22:23:04

赞赞赞！它是怎么运行的啊？

花生编程 发表于 2023-8-5 22:24:08

有演示的视频看吗？

查看完整版本: 激光切割+编程 时针